"FOR
SALE"
AMPS
NOTE: The Canadian & US Dollar are virtually at par.
Therefore, unless otherwise noted, they are the same.
$100.00 CAD = $100.00 USD
Some existing product (in stock & on order) was purchased at
a higher Exchange Rate, so as with any retail situation,
it will take several months for price adjustments to take effect,
until
existing stock is replenished.
Prices are subject to change without notice.
SGC
is an Authorized Peavey® Dealer
SGC is now an Authorized Fender® Dealer
NEW
& USED STEEL AMPS
Amps:
Used Evans
RE150 Solid State, 150 watts w/10” Eminence Delta-Lite speaker, Digital Reverb,
Headphone Jack, w/cover, Excellent (like new) Condition - $895.00 CAD
Used Peavey PX-300 Powered Speaker, w/cover, Excellent (like new) Condition - $775.00 CAD
PEAVEY® Amps
(Contact SGC for pricing)
~ New
Peavey® Nashville 112 Amps are in stock, 80 watts, w/12 inch speaker,
headphone jack & more. <Contact SGC for
Pricing!>
~ New
Peavey® Nashville 1000 Amps are in stock, 250 watts, w/15 inch BW
speaker. <Contact SGC for Pricing!>
Peavey Amp
Accessories:
~ SGC has the
Mod Kits for the Nashville 112 & Nashville 1000 amps @ $58.00
(Includes the circuit board diagram
for installation).
~ SGC has the
Peavey Tone Kits for:
-Nashville 400 amps @ $40.00 per
kit,
-Vegas 400 amps @ $40.00 per kit,
-Session 400 Limited amps @ $50.00
per kit,
-Session 500 amps @ $37.00 per kit,
-Pro-Fex II @ $26.00.
(Includes the circuit board diagram
for installation).
~
New Peavey® Amp Stands are in stock - $55.00
Covers for Peavey Amps:
-for Nashville 400….Reg. Vinyl @ $49.00; D2F (Designed To Fit) @ $60.00
-for Nashville 112….Reg. Vinyl @ $49.00; D2F (Designed to Fit)@ $55.00
-for Nashville 1000… Peavey @ $35.00; D2F (Designed to Fit) @ $65.00
~ Peavey® EDI
(Equalized Direct Interface) units are now in stock. This box installs between
the power amp output & the speaker to give you a XLR line out to a mixing
console, reproducing the same sound as putting a mic on the speaker, but with
no signal bleeding, or mic stand clutter, etc. It can also double as a
headphone output, (eliminating the amp’s speaker sound)…very useful for tuning
or practicing!
~
Peavey® 1501-4 BW RB (replacement baskets for Black Widow speakers….in stock)
~
Peavey® 1501-4 BW SB Black Widow speakers (On Order).
FENDER® Amps
~ Fender Steel King, 200 watts, w/15”
Custom Speaker (designed after the JBL D130F), w/Foot Switch, Casters, &
Cover – <Contact SGC
for Pricing!>
EVANS
CUSTOM AMPLIFIERS
|
The goal at Evans is to provide
artists with the best possible amplifier value. This goal is consistently reached
through input from top professionals who depend on Evans amps for their
sound. |
||||||
|
Canadian Dealer
Steel
Guitars of Canada,
566 Dudley Rd., R.R. # 5,
COLBORNE,ON K0K 1S0
Phone: 905-355-3056 ~ Fax: 905-355-2811
E-Mail: steelcan@steelguitarcanada.com
Web Site: http://www.steelguitarcanada.com
Contact Al
Brisco for your Evans Amp
NOTE: All prices listed in Canadian Dollars.
May 2008
|
|
|||
|
Evans Console
Amplifiers |
|||
|
|
RE200 Confirms
That Great Tone Can Come in Small Packages! |
||
|
|
||
|
|
||
|
|
||
|
|||
|
Solid State RE200 |
List: $1548 USD |
Your SGC Cost $1255 CAD |
|
|
Hybrid RE200 |
List: $1848 USD |
Your SGC Cost $1540 CAD |
|
|
|
JE200 Twice
the Bite, Twice the Bark! |
||
|
|
||
|
|
||
|
|
||
|
|||
|
Solid State JE200 |
List: $1611 USD |
Your SGC Cost $1325 CAD |
|
|
Hybrid JE200 |
List: $1911 USD |
Your SGC Cost $1615 CAD |
|
|
|
SE200 Experience
Clean, Crisp, Full Range Tone!
|
||
|
|
||
|
|
||
|
|
||
|
|||
|
Solid State SE200 |
List: $1748 USD |
Your SGC Cost $1440 CAD |
|
|
Hybrid JE200 |
List: $2048 USD |
Your SGC Cost $1730 CAD |
|
|
|
AH200 Compact
& Portable With a Knockout Punch! |
||
|
|
||
|
|
||
|
|||
|
Solid State AH200 |
List: $1274 USD |
Your SGC Cost $995 CAD |
|
|
Hybrid SE200 |
List: $1574 USD |
Your SGC Cost $1285 CAD |
|
Extension
Speaker Cabinets
…provide extra coverage with increased power…
|
|
RES200 Really
Spits Out The Notes! |
||
|
|
||
|
|||
|
|||
|
RES200 |
List: $707 CAD |
Your SGC Cost $599 CAD |
|
|
|
JES200 Full
Range Sound! FEATURES: |
||
|
|
||
|
|||
|
|||
|
JES200 |
List: $800 CAD |
Your SGC Cost $680 CAD |
|
|
|
SES200 Big
Expansive Sound! FEATURES: |
||
|
|
||
|
|||
|
|||
|
SES200 |
List: $890 CAD |
Your SGC Cost $755 CAD |
|
The Amplifier Head 200 is now
available with an optional all tube preamp. Artists will discover all the familiar
front panel controls: Master, Reverb, Bass, Depth, Body, Expand, Treble, and
Volume with easy to read and adjust knobs. These controls deliver the tonal
adjustability & clarity that top musicians depend on. Other features
include: +6dB and Normal inputs, effects loop, headphone and external speaker
capability, and preamp output. NEW reverb effects include: Reverb alone, Flange
& Reverb, or Chorus & Reverb. Also, a new Dwell control allows you to
adjust the desired amount of layout for the selected reverb effect.
The all-tube preamp Hybrid combo amplifiers have already garnered praise from
some of our top endorsers. They were astounded by the amp's sweet, warm tone.
They also appreciated the lack of hum and lag associated with other tube
amplifiers, making the Hybrid Evans amps ideal for the recording studio.
Also, all the power amps are 200
watts, & are switchable between 115V & 230V, so they can be used
‘world-wide’, simply by changing the power cord plug to suit the country where
it is being used.
If you appreciate the tone of high quality instruments, then you owe it to
yourself to experience just how good they can sound by arranging to audition a
new hybrid Evans Custom Amplifier today.
Evans Custom Amplifiers has been blessed with over 40 years
of continuously building great amps by closely following the vision of our
founder and current chief consultant, Jim Evans. Now, you can easily experience
the uncluttered sound that has made Evans Amps the pinnacle of clean
amplification worldwide. Order Today.
Operating Controls
Pictured - top front panel
Pictured - top front panel
NORMAL AND +6Db INPUTS: +6Db provides the most volume with a heavier amplified sound. Use Normal Input with strong pickups to avoid overdriving the preamp. (+6Db = Input 1 and Normal = Input 2 on older models). Located on top front panel.
MASTER: Used to set the output gain of the preamp. On newer models the convenient on/off switch on this knob requires the first part of the control. So, don't be afraid to turn it from 3 to 7. Located on top front panel.
BUFF: This solid state preamp control provides beautiful overtones found in tube amplifiers. Start with Buff on 4 to 6. Next, use your ear to adjust the Treble then the Expand switch. Located on top front panel. (Models made before 2004 had the Scruff control which warmed the sound while cutting some of the highs and was not recommended for Pedal Steel Guitar.)
REVERB: This control mixes in the amount of reverb effect desired. Digital reverb now standard on Evans Amplifiers. Located on top front panel.
REVERB SELECTION: A rear panel switch selects Reverb alone, Reverb plus Flange, or Reverb plus Chorus. (Currently unavailable with Solid State AH200.)
DWELL: This rear panel control sets room size or reverb interval. The Dwell control has a convenient center detent value sufficient for most musicians. (Currently unavailable with Solid State AH200.)
BASS: Sets the amount of bass desired. The maximum Bass should be dialed in by playing the lowest open string and turning up the knob from 0 until it gets boomy and then backing off by a number. Turn down the Bass to 5 or less when using +6Db Input with Master greater than 6 or Normal Input with Master greater than 7. If the Bass knob is turned up while playing at loud volume, the low end will be overcompensated and muddy because bass frequencies are easier to reproduce at loud volumes. Located on top front panel.
DEPTH: This control enhances the low and low midrange. Counterclockwise to 7 o'clock is off. Turn to 7 o'clock - 12 o'clock when Master is greater than 5 in +6Db Input or 7 with Normal Input. Body knob must be set > 1 for best Depth operation. Located on top front panel.
BODY: Used to set the amount of midrange and darkness, this is a multi-function control that increases low mid-range tones while rolling off high frequencies. Located on top front panel.
EXPAND: This switch boosts the highs, and some lows. Up is on, down is off. Located on top front panel.
TREBLE: Selects the amount of treble desired. On new models the Treble should be dialed in by playing the highest open string and turning up the knob from 0 until it gets thin and then backing off by a number. The most solid Treble sound is 0-2. Located on top front panel.
VOLUME: Sets the input level to the pre-amp. Lower settings (3-5) reflect the instrument's voice. Higher settings (6-9) emphasize the amplifier's tone settings. Located on top front panel.
EFFECTS OUT AND IN (SEND AND RETURN): These jacks are located on the top back panel and placed in the circuit just before the Master level control and after all frequency adjustments and reverb. Most effects units should be connected here. However, some effects units may operate better connected between the instrument and Normal Input.
PREAMP OUT: This is a line out signal for driving a mixer board or an additional power amplifier. (1/4" jack available) Located on top back panel.
EXTERNAL SPEAKER: The output is used for driving an additional 8 ohm speaker. Located on bottom back panel.
PHONES: Jack for headphones. Located on bottom back panel.
Direct
Link to Evans Amps...for more
information.
Click
here to see “Steel
Guitars In Stock” available for sale!
Misc. Accessories:
Used
Pickups:
-1
x Wallace True-Tone (Wide Mount) 17.5 ohm, like new single coil pickup -
$90.00
-1
x Emmons Single Coil, (wide mount) pickup - $95.00
-Bill Lawrence LXR-16 Wide Mount 12 string pickups - $155.00
For
our complete ‘Pickups’ selection, go to: PICKUPS
Pedals, Tuners, etc.:
- PEC
500K pots for steel guitar volume pedals - $29.00
·
Used Goodrich Model 60 Match-Box (buffer amp)
- $75.00
- New
Carter Volume Pedal - $150.00
·
New Peavey EDI (Equalized Direct Interface),
used in place of miking your amp. Note:
This unit can also be used as a headphone jack. - $65.00
Seats & Benches:
- New
Quik-Lok Model BX716 (Pro Bench Seat) 17.1”/19.3”/20.8”/22.4”Height
Positions - $70.00
- New
Ultra KT216 Keyboard-type Bench Seat, adjusts from 18” to 21” height -
$79.00
- New
SGC ‘Real Seat’, Flight Case seat, Cushion stores inside, 2 volume pedal
compartments, 3 compartments for strings, cables, etc. [A
‘must-have’ if you fly] - $395.00
- New
Out West Country Pac-seat, Standard Size, Black cloth seat
(wheelchair-type), Black laminate sides - $340.00
Out West
Country ~ Standard Pac-seat
- GFI
Standard Kari-All Storage Seat, Grey Carpet w/Vinyl Seat Cover - $295.00
Cases:
- New
Cases for Carter-Starter guitars - $135.00
- New
Cases for Carter D-10 or S-10DB - $195.00
- New
SKB Model H3611W ‘Wheel-Eze Type’ Case, 36” x 11” I.D. - $250.00
- ‘Signature
Sound’ Flight Case, for lap steel, I.D. 34½” x 8” x 2½” (88cm x 21cm x
6cm) - $295.00
- ‘Signature
Sound’ Flight Case, Compact but Strong, for Emmons Original or
LeGrande D-10, (example shown is for Carter D-10), only 4 lb heavier than
standard case - $465.00
- ‘Signature
Sound’ Flight Case, Compact but Strong, (example shown is for Carter
D-10), only 4 lb heavier than standard case - $465.00
Signature Sound
Flight Case ~ Signature
Sound Flight Case open
“Walker Steeler Seats”
·
NOTE: We
always have steels, amps, etc. coming & going, so please don't hesitate to Mail to SGC for the latest
list of available steel guitars, amps, accessories, etc.
John LeMay's
Miracle Audio
Originators
of High Performance Modifications
Of
Steel Guitar amps Since 1992
Now available in Canada,
from
Steel Guitars of Canada
John LeMay's 'Miracle Audio' has
over 6 years of satisfied customers including Tommy White, Rufus Thibodeaux,
Robby Turner, Bruce Bouton, George Edwards, Al Brisco, Joe Rogers, Larry Behm,
Keith Holter, Jerry Gleason, & more.
What
is the 'Mod'?
To achieve the high performance
that the "Super Mod" modification brings to Peavey amps, the
signal is cleaned up while the harshness and distortion are eliminated.
The 'Mod' adds dramatically
better transient response and greatly decreases noise. The result is a
transparent, smooth, clean sound with added sustain, tight bottom and silky
highs. The 3rd & 4th strings don't "stick out" anymore. The tone
is balanced across the neck. Greatly increased string separation allows complex
chordal passages with all of the counterpoint to be heard clearly. Upper
harmonics are heard easily and the cleanliness of the signal is superlative.
Players have reported nearly doubled sustain.
The modification is
designed to be extremely road worthy. Any component technician can service the
unit should that ever be necessary. There are no special add-on boards to worry
about, no widgets to break and leave you stranded. All mods are done within the
constraints of the original construction to maximize dependability.
What
amps can be modified?
We only have LeMay kits
remaining for the following Peavey amps: Nashville 400, Vegas 400, Session 500,
The Session 400 Limited (post 1987).
Customer's
comments about the 'mod'....
John...The first amp you did for me was super, the
best I've ever heard. I'm getting ready to send you the second amp probably
this week. I'm looking forward to the second amp as I'm sure it will be as good
or better than the first. I've had nothing but great comments and praise on the
first amp that you did for me. Thanks Again!
George Edwards
Kitty Wells Show, Nashville, TN
"I have
the first SUPER MOD. Clean and clear, in your face real steel tone finally. I
am a tone freak pure and simple. I don't make one penny from John...I was just
the first to do it. I would spend the money again. This is clean, like no other
amp you have ever heard. If any of you have any questions, call me at
503-786-4460. You have nothing to lose and everything to gain."
Larry Behm
Hi John,
I got the Session 500 Super Mod kit in Friday's mail.
The kit was extremely easy to install, given your very clear instructions. I
took my time, and everything went well. Then I sat down to play, and wow!! It's
everything they claim it to be! I feel as if I have a new amplifier! The tone
is terrific, and I seem to have much more gain. I typically use a Goodrich
Steel Driver II, and the system even sounds great without it now. I'm just so
pleased!!
Best Regards,
Don Walters, Regina, SK
John,
I am very pleased with my Nashville amp...it has
never sounded so good. The increase in gain is a much welcomed improvement. The
bright switch feature is the icing on the cake. I am glad there is someone who
cares enough about tone to take the time and trouble to develop such a
wonderful process. Keep up the good work.
Jackie Harmon, Sherman, TX
Products & Services Offered
The Super Mod Kit
It's
for the purist, who wants the best his amp can deliver. The Super Mod delivers
the ultimate in steel sound. It gives you tremendous string separation,
over-tones and harmonics you've never been able to hear before. No more harsh
tone. Just pure sweetness...with punch!
These
kits include all of the parts needed to modify your amp for maximum
performance. Included are diagrams, instructions and trouble shooting
techniques. These kits require a basic skill in soldering and unsoldering.
Ideal for the home electronics hobbyist with a basic degree of skill.
Average
time to do an amp mod is about 3 - 4 hours, depending on skill level.
Costs
of the Super Mod Kits: (Canadian Dollars)
-Peavey Session 400 Limited (1987 and
newer)...
Kit - $155.00 ~ Installed by Al Brisco
- $200.00 (One only)
NOTE:
We suggest shipping only your amp chassis, when having Al do the install.
(Shipping
charges & taxes are extra)
Make
payments payable to Steel Guitars of Canada.
NOTE:
For More Detailed ORDERING INSTRUCTIONS, (re: International Orders, etc.), go
to ORDERING INSTRUCTIONS
You may go to ORDER FORM,
Print it & use to mail or fax your order.
To
check out more For Sale items, go to FOR SALE.
Back
To SGC Steel Post/Home
Page
We
welcome your suggestions about our Site via Email: steelcan@steelguitarcanada.com
steelcan@steelguitarcanada.com
Steel Guitars of Canada Web Site.